Timber & Masonry construction

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls

The MHA is a galvanised mini joist hanger suitable for use with regularised timber, rough sawn timber, I-Joists and LVL.

Ideally suited for small timber sections and timber members; such as trimmers and ceiling joists

The H and L straps are designed to The Building Regulations for
horizontal and vertical restraint.

• Heavy restraint straps meet requirements for lateral restraint of roof trusses, rafters and joists tied into masonry walls.
• Light restraint straps are designed for vertical loads such as wall plates on top of masonry walls.
• All common sizes in stock from 500 to 2000mm long, 100mm increments. Longer lengths avaialble to order; contact technical support.

The H and L straps are designed to The Building Regulations for
horizontal and vertical restraint.

• Heavy restraint straps meet requirements for lateral restraint of roof trusses, rafters and joists tied into masonry walls.
• Light restraint straps are designed for vertical loads such as wall plates on top of masonry walls.
• All common sizes in stock from 500 to 2000mm long, 100mm increments. Longer lengths avaialble to order; contact technical support.

The H and L straps are designed to The Building Regulations for
horizontal and vertical restraint.

• Heavy restraint straps meet requirements for lateral restraint of roof trusses, rafters and joists tied into masonry walls.
• Light restraint straps are designed for vertical loads such as wall plates on top of masonry walls.
• All common sizes in stock from 500 to 2000mm long, 100mm increments. Longer lengths avaialble to order; contact technical support.

The H and L straps are designed to The Building Regulations for
horizontal and vertical restraint.

• Heavy restraint straps meet requirements for lateral restraint of roof trusses, rafters and joists tied into masonry walls.
• Light restraint straps are designed for vertical loads such as wall plates on top of masonry walls.

Heavy duty restraint strap made from 30mm x 5mm galvanised edge coated steel for lateral restraint of roof trusses, rafters and joints tied into masonry walls. Designed to The Building Regulations, BS5268 pa3 and other building standards for horizontal restraint when connecting timber floor and roof systems to masonry walls.

Simpson Strong-Tie Fixing Band is for all general light strapping needs and can be easily bent or twisted for many versatile installations. No load rating provided and not recommended for structural applications.

The TCP truss clip attaches girders, trusses and rafters to wall plates to provide wind restraint.

• TCP Truss Clips may be used for general purposes, strongback attachments as allpurpose ties wherever one member crosses another.
• Speed prong provides temporary attachment for ease of installation.
• Obround holes for easier nail driving.

Type 2 wall ties are suitable for general purpose applications such as domestic and small commercial buildings up to 15m in height. They can also be used in buildings with heights exceeding 15m, but should only be used in those situations if shown to be of adequate performance by calculation. Use in flat sites where the basic wind speed is up to 31 m/s and the altitude is not more than 150m above sea level.

Type 2 wall ties are suitable for general purpose applications such as domestic and small commercial buildings up to 15m in height. They can also be used in buildings with heights exceeding 15m, but should only be used in those situations if shown to be of adequate performance by calculation. Use in flat sites where the basic wind speed is up to 31 m/s and the altitude is not more than 150m above sea level.

Type 2 wall ties are suitable for general purpose applications such as domestic and small commercial buildings up to 15m in height. They can also be used in buildings with heights exceeding 15m, but should only be used in those situations if shown to be of adequate performance by calculation. Use in flat sites where the basic wind speed is up to 31 m/s and the altitude is not more than 150m above sea level.

Type 2 wall ties are suitable for general purpose applications such as domestic and small commercial buildings up to 15m in height. They can also be used in buildings with heights exceeding 15m, but should only be used in those situations if shown to be of adequate performance by calculation. Use in flat sites where the basic wind speed is up to 31 m/s and the altitude is not more than 150m above sea level.

WTS4: Type 4 Wall Ties: Masonry Light Duty
Type 4 wall ties are light duty, suitable for box-form dwellings up to 10 metres high with leaves of similar thickness, including internal separating cavity walls. Use in flat sites in towns and cities where the basic wind speed does not exceed 25 m/s and the altitude is not more than 150m above sea level.

WTS4: Type A Approval
WTS4-200 and WTS4-225 ties meet the requirements of Approved Document E: Resistance to the Passage of Sound and are suitable for use in separating party walls of new build attached dwellings.

WTS4: Type 4 Wall Ties: Masonry Light Duty
Type 4 wall ties are light duty, suitable for box-form dwellings up to 10 metres high with leaves of similar thickness, including internal separating cavity walls. Use in flat sites in towns and cities where the basic wind speed does not exceed 25 m/s and the altitude is not more than 150m above sea level.

WTS4: Type A Approval
WTS4-200 and WTS4-225 ties meet the requirements of Approved Document E: Resistance to the Passage of Sound and are suitable for use in separating party walls of new build attached dwellings.

WTS4: Type 4 Wall Ties: Masonry Light Duty
Type 4 wall ties are light duty, suitable for box-form dwellings up to 10 metres high with leaves of similar thickness, including internal separating cavity walls. Use in flat sites in towns and cities where the basic wind speed does not exceed 25 m/s and the altitude is not more than 150m above sea level.

WTS4: Type A Approval
WTS4-200 and WTS4-225 ties meet the requirements of Approved Document E: Resistance to the Passage of Sound and are suitable for use in separating party walls of new build attached dwellings.

WTS4: Type 4 Wall Ties: Masonry Light Duty
Type 4 wall ties are light duty, suitable for box-form dwellings up to 10 metres high with leaves of similar thickness, including internal separating cavity walls. Use in flat sites in towns and cities where the basic wind speed does not exceed 25 m/s and the altitude is not more than 150m above sea level.

WTS4: Type A Approval
WTS4-200 and WTS4-225 ties meet the requirements of Approved Document E: Resistance to the Passage of Sound and are suitable for use in separating party walls of new build attached dwellings.