Timber & Masonry construction

Reinforced angle brackets are suitable for structural applications in framing and timber framed houses as well as light gauge steel construction.

Reinforced angle brackets are suitable for structural applications in framing and wood-frame houses.

The C2K Crocodile Wall Starter is a quality engineered wall connector
system that has been developed for use with most brick and block
modules. This system has been designed for multi-purpose use where
reliability and durability are important requirements. It provides lateral
support to masonry wall panels in conversion, extension and new
building work.

• BBA Approved for up to 8m, 3 storey work.
• Accommodates 10mm of vertical movement.
• Adjustable anchor ties to accommodate variation in brick courses.
• All fixings and ties provided within the packs.

Light reinforced angle brackets are used to assemble small structural joinery for internal and external applications.
 

Light reinforced angle brackets are used to assemble small structural joinery for internal and external applications.
 

Light reinforced angle brackets are used to assemble small structural joinery for internal and external applications.

Light angle brackets are used in a large number of DIY applications and are commonly used for reinforcing furniture assemblies.

Light angle brackets are used in a large number of DIY applications and are commonly used for reinforcing furniture assemblies.

EFIXR angle brackets are intended for all assemblies for the design and installation of interior and exterior joinery. EFIXR stiffener improves rigidity particularly for large models.

Simple angle bracket which is very versatile, used for timber to timber connections.

When fixing windows, door frames etc. to masonry, the frame tie provides
enhanced mortar keying and reduces the risk of injury from sharp edges.

Note: Frame tie should be fully embedded into mortar.

SAE and SAI ranges are heavy-duty hangers designed for applications requiring additional strength.

SAE hangers are nailed using square twist nails but have bolt holes for 12mm fasteners into the face. SAE Timber Bolted capacity to be determined according to the relevant standards.
The hanger depth is to be at least 60% of the carried member depth to prevent rotation, unless additional lateral restraint is added to the top of the carried member.

Reinforced angle brackets are suitable for structural applications in framing and wood-frame houses.

Reinforced angle brackets are suitable for structural applications in framing and wood-frame houses.

A direct replacement for traditional restraint straps, the innovative design of these lightweight straps allows ease of handling and installation whilst maintaining the structural strength and robustness of much heavier weight types.
The HES (heavy engineered strap) replace the traditional heavy (30 x 5mm) restraint straps in roof and floor construction.
Reduced thickness allows the HES strap to span the bottom chords of trusses and over floor joists without the need for notching.
HES straps are less than 40% of the weight, quicker to fit, and overcome many fixing problems associated with traditional heavy straps.

• Formed edge design gives additional strength on bend
• Quicker to install - can fit over top of floor joists and truss bottom chords
• Easier to course with blockwork
• No need to notch joists
• Complies with BS EN 845-1

JHA is a height adjustable joist hanger for supporting timber joists from timber members.

It is available in standard leg (JHA270) and long leg (JHA450) versions and can be installed to the face of the carrying joist or wrapped over the top for higher performance.

JHA is a height adjustable joist hanger for supporting timber joists from timber members.

It is available in standard leg (JHA270) and long leg (JHA450) versions and can be installed to the face of the carrying joist or wrapped over the top for higher performance.

JHA is a height adjustable joist hanger for supporting timber joists from timber members.

It is available in standard leg (JHA270) and long leg (JHA450) versions and can be installed to the face of the carrying joist or wrapped over the top for higher performance.

JHA is a height adjustable joist hanger for supporting timber joists from timber members.

It is available in standard leg (JHA270) and long leg (JHA450) versions and can be installed to the face of the carrying joist or wrapped over the top for higher performance.

JHA is a height adjustable joist hanger for supporting timber joists from timber members.

It is available in standard leg (JHA270) and long leg (JHA450) versions and can be installed to the face of the carrying joist or wrapped over the top for higher performance.

JHA is a height adjustable joist hanger for supporting timber joists from timber members.

It is available in standard leg (JHA270) and long leg (JHA450) versions and can be installed to the face of the carrying joist or wrapped over the top for higher performance.

JHA is a height adjustable joist hanger for supporting timber joists from timber members.

It is available in standard leg (JHA270) and long leg (JHA450) versions and can be installed to the face of the carrying joist or wrapped over the top for higher performance.

masonry hanger for solid joists  for supporting timber beams, joists and trussed rafters from masonry walls

masonry hanger for solid joists Ideal for supporting timber beams, joists and trussed rafters from masonry walls